SW180AB-51 is an 48 volt intermittent contactors by design are predominantly used for hydraulic functions on vehicles, they make and break quicker than continuous solenoids and are not recommended for prolonged contact periods.
The SW180AB has been designed for direct current loads, including motors as used on electric vehicles such as industrial trucks. Developed for both interrupted and uninterrupted loads, the SW180B is suitable for switching Resistive, Capacitive and Inductive loads.
The SW180AB features single pole single throw, double-breaking main contacts with silver alloy tips, which are weld resistant, hardwearing and have excellent conductivity.
The SW180B has M8 stud main terminals and 6.3mm spade coil connections. It can be mounted via M5 tapped holes or steel mounting brackets - supplied as separate items). Mounting can be horizontal or vertical, when vertical the M8 contact studs should point upwards.
Albright HV500F-21 – High Voltage Electromechanical DC ContactorThe Albright HV500F-21 is a hermetically sealed electromechanical DC contactor in the HV500 family, designed to switch DC power using physical main contacts. It is not a solid-state relay. The listed 24V DC refers to the control-coil voltage, not the voltage switched by the main contacts.Key features
Electromechanical switching with normally open (NO) main contacts
Hermetically sealed high-voltage DC contactor design
HV500 family specifications include high-voltage operation up to 1000V DC, subject to application-dependent ratings
High-current switching for properly engineered DC circuits; verify continuous, making and breaking ratings for the specific operating conditions
Configuration and applicationsThe product listing identifies a PWM coil economiser. PWM manages the contactor coil and does not make the main contacts solid-state.Typical application areas include electric vehicles, battery packs, DC charging, renewable energy, energy storage and industrial DC distribution, where the part's voltage and current capabilities meet system requirements.Engineering note: HV500 contactors do not replace external fuses, circuit breakers, or suitable pre-charge arrangements. Verify current and voltage under load, coil supply, operating duty, auxiliary contacts, mounting and environmental requirements for the exact model.Manufacturer reference: Albright HV500 product family.
Product overviewONE Light LED Driver 89100V.100W 24V DC constant voltage driver, IP20. Complies with standard EN61347-1 and any other specific standards.Key specifications
Product code: 89100V
Type: LED Driver
Category: 22 Drivers
Family: The 24V DC Range High Power Constant voltage
Material: Plastic
Length: 170mm
Width: 45mm
Height: 28mm
Warranty: 5 Years
Downloads & links
Datasheet
Manufacturer page
Product overviewONE Light LED Driver 89320X.320W 48V DC constant voltage driver, IP20. Complies with standard EN61347-1 and any other specific standards.Key specifications
Product code: 89320X
Type: LED Driver
Category: 22 Drivers
Family: The 48V DC Range Constant voltage
Material: Plastic
Length: 210mm
Width: 80mm
Height: 37mm
Warranty: 5 Years
Downloads & links
Datasheet
Manufacturer page
Product overviewONE Light LED Driver 89150VPL.15-150W 24V DC DALI & Push to DIM dimmable constant voltage driver, IP67. Complies with standard EN61347-1 and any other specific standards.Key specifications
Product code: 89150VPL
Type: LED Driver
Category: New 2025 Edition 2
Family: Drivers
Material: Metal
Length: 380mm
Width: 37mm
Height: 21mm
Warranty: 5 Years
Downloads & links
Datasheet
Manual
Manufacturer page
Magnetic Blowouts These open case contactors are of double break configuration and are fitted with magnetic blowouts - denoted by 'B' suffix in the SW60B range) across both contact gaps. These enable high currents to be ruptured very quickly so that arcing time is reduced to a minimum. Fitting of blowouts makes the contacts polarity sensitive and the positive markings on the top cover of the contactor must be observed.About Continuous - CO.) SW60B Solenoids Continuous contactors by design are predominantly used for drive functions on vehicles, they make and break slower than intermittent solenoids and are recommended for prolonged contact periods. The SW60B features single pole double breaking main contacts with silver alloy tips, which are weld resistant, hardwearing and have excellent conductivity. The SW60B has M6 stud main terminals and 6.3mm spade coil connections. It can be mounted via M4 tapped holes or steel mounting brackets - supplied as separate items). Mounting can be on the side or base of the contactor.
SW60-40P Albright 24V DC CO
Continuous contactors by design are predominantly for drive functions on vehicles, they make and break slower than intermittent solenoids and are recommended for prolonged contact periods.
The SW60-40P features single pole double breaking main contacts with silver alloy tips, which are weld resistant, hardwearing and have excellent conductivity. The SW60P incorporates an enclosed top cover and offers environmental protection to IP66. The SW60P has M6 stud main terminals and 6.3mm spade coil connections.
Genuine SW60B-514 ALBRIGHT 80V 80A CO DC Contactor.
The SW60B-514, an Albright SW60 series version equipped with magnetic blowouts - B) is a miniature series single pole contactor. SW60B is free-standing and compact, designed to fill the gap between 30 amperes and 100A /125A contactors.
Product overviewONE Light LED Driver 89150V.150W 24V DC constant voltage driver, IP20. Complies with standard EN61347-1 and any other specific standards.Key specifications
Product code: 89150V
Type: LED Driver
Category: 22 Drivers
Family: The 24V DC Range High Power Constant voltage
Material: Plastic
Length: 205mm
Width: 71mm
Height: 35mm
Warranty: 5 Years
Downloads & links
Datasheet
Manufacturer page
Genuine SW80-374P Albright Contactor. The SW80-374P, a Albright SW80 -series contactor with IP66 protection - P), has been developed for direct current loads, including motors as used on different kind of electric vehicles like industrial trucks as well as
