LED Adapters & Flash Prevention

24 Volt resistor replacement load for the adaptation of light-emitting diode (LED) trailer lamps at vehicles with incandescent lamp monitoring. The failure of an LED unit is indicated and the replacement load is turned off. LED-ADAPT must be mounted on a metal surface. ***CAUTION*** The connection of any bulb on the output is prohibited. The overcurrent protection may cut off not until after several minutes! ▪ Operating voltage: 24V nominal▪ Input: open cable end▪ Output: open cable end Weight: 1.68 kg simply connect ahead of LED lamps LED-failure is indicated a short circuit is indicated Serves all lines with replacement resistors Input cable 3,5m can be connected directly to the plug Operation voltage: 24V nominal Output current: 0.4A (Over current protection time delay 1...2000s !) Connection input: Sheathed cable 8x1mm², bare endings Connection output: Sheathed cable 8x1mm², bare endings Load imitation: 2x17 W (direction), 2x4W (rear lamp), 1x34W (stoplight) 1x17W (fog lamp), 1x17W (reversing lamp) Cable length input: app. 3,5m Cable length output: app. 1,2m Temperature range: -40...+75°C Electrical protection: Overcurrent, overtemperature, reverse polarity Mechanical protection: entirely sealed Dimensions: 280 x 70 x 25mm without cable outlet Mass: app. 1680g Failure monitor LEDs: 20mA (direction) 3mA (rear lamp) 8mA (stoplight) 8mA (fog lamp) 20mA (reversing lamp) Mounting rule: cooling plate 8dm² (aluminum sheet 1.5mm thickness) or on chassis frame

Read more less

The Flash-Prevent prevents effectively the inadmissible flashing of LED lamps caused by the vehicle's pulsed cold scan ("hard" and short pulse  ab. 10ms). The failure of an LED will be monitored.Attention! Flash-Prevent doesn't replace LED-ADAPT.▪ Prevents flashing of LED lamps▪ LED failure detection stays in function▪ Easy installation ahead of to the LED▪ possible to install inside the lamp housingWeight 27gEffectively prevents flashing of LED lamps The failure detection stays in function Easy installation due to compact dimensions Easy installation ahead of to the LED lamps Completes LED-ADAPT in combined monitoring Operation voltage: 24V nominal Output current: LED (max 0.4A) Connection input: strand with bare endings Connection output: strand with bare endings Load imitation: within 0-50ms cold filament Cable length input: 0.30 m Cable length output: 0.30 m Temperature range: -40...+75°C Electrical protection: __ Mechanical protection: entirely sealed (IP69K) Dimensions: 40 x 18 x 15 mm without cable outlet Mass: approx. 27g Failure monitor LEDs: integrated Mounting rule: __

Read more less

The Flash-Prevent prevents effectively the inadmissible flashing of LED lamps caused by the vehicle's pulsed cold scan ("hard" and short pulse  ab. 10ms). The failure of an LED will be monitored.Attention! Flash-Prevent doesn't replace LED-ADAPTER.▪ Prevents flashing of LED lamps▪ LED failure detection stays in function▪ Easy installation ahead of to the LED▪ possible to install inside the lamp housing Weight: 0.03 kg Effectively prevents flashing of LED lampsThe failure detection stays in functionEasy installation due to compact dimensionsEasy installation ahead of to the LED lampsCompletes LED-ADAPT in combined monitoring Operation voltage: 12V nominal Output current: LED (max 0.4A) Connection input: strand with bare endings Connection output: strand with bare endings Load imitation: within 0-50ms cold filament Cable length input: 0.30 m Cable length output: 0.30 m Temperature range: -40...+75°C Electrical protection: __ Mechanical protection: entirely sealed (IP69K) Dimensions: 40 x 18 x 15 mm without cable outlet Mass: approx. 27g Failure monitor LEDs: integrated Mounting rule: __

Read more less

12 Volt resistor replacement load for the adaptation of light-emitting diode (LED) trailer lamps at vehicles with incandescent lamp monitoring. The direction indicator lamps and the contacts 9 to 13 are looped. LED-ADAPT must be mounted on a metal surface. Important: The direction indicators must be incandescent lamps or LEDs with their own monitoring. Other lines may have additional load of 10W maximum, in this case monitoring is disabled.▪ Operating voltage: 12V▪ Input: 12V 13-pol plug▪ Output: 12V 13-pol socket Weight: 2.85 kg Ready for use solution with 13 pin standard connectors Configuration: "2 incandescent lamps + 5 LED + contacts 9 to 13" No cabling work needed The additional pins 9 to 13 are looped Retrofitting for a factory finished trailer in case of incompatibility with a new vehicle Failure of an LED is detected (if no incandescent lamp is connected in parallel) Operation voltage: 12V nominal Output current: 0.8A (Over current protection time delay 1...2000s !) Connection input: Male connector 13-pin 12V ISO'11446 Connection output: Female socket with flap cover 13 pin 12V ISO'11446 Load imitation: 2x4W (rear lamps), 1x34W (stoplight) 1x17W (fog lamp), 1x17W (reversing lamp) Cable length input: app. 3300mm Cable length output: app. 600mm Temperature range: -40...+75°C Electrical protection: Overcurrent, overtemperature, reverse polarity Mechanical protection: entirely sealed Dimensions: 280 x 70 x 25mm without cable outlet Mass: app. 2850g Failure monitor LEDs: 3mA (rear lamp) 8mA (stoplight) 8mA (fog lamp) 20mA (reversing lamp) Mounting rule: cooling plate 8dm² (aluminum sheet 1.5mm thickness) or on chassis frame, lamp configuration only 2 x incandescent lamps + 5xLED(+0...10W)

Read more less

12 Volt resistor replacement load for the adaptation of light-emitting diode (LED) trailer lamps at vehicles with incandescent lamp monitoring. The failure of direction indicators is indicated.***CAUTION*** LED-ADAPT must be mounted on a metal surface. The connection of any bulb on the direction indicator output is prohibited. The overcurrent protection may cut off not until after several minutes! ▪ Operating voltage: 12V nominal▪ as ballast for LED direction indicators▪ operates right and left turn signals Weight: 0.35 kg Single cable version LED direction indicator monitoring Serves the direction indicators with replacement resistors Conditionally short circuit proof (about 100 cycles) Operation voltage: 12V nominal Output current: max. 0.4A (direction) (Over current protection time delay 1...2000s!) Connection: Hose line 5x1mm², ins. 6.3mm blade receptacle Load imitation: 2x17W (direction) Cable length: 0.25 m Temperature range: -40...+75°C Electrical protection: Overcurrent, overtemperature, reverse polarity Mechanical protection: Entirely sealed (IP69K) Dimensions: 120 x 70 x 25mm Mass: app. 350g Failure monitor LEDs: 20mA (direction) Mounting rule: Cooling plate 8dm² (aluminum sheet 1.5mm thickness) or on chassis frame

Read more less

12 Volt resistor replacement load for the adaptation of light-emitting diode (LED) trailer lamps at vehicles with incandescent lamp monitoring. The failure of a LED unit is indicated and the replacement load is turned off. LED-ADAPT must be mounted on a metal surface. ***CAUTION*** The connection of any bulb on the output is prohibited. The overcurrent protection may cut off not until after several minutes! ▪ Operating voltage: 12V nominal▪ Input: open cable end▪ Output: open cable endWeight: 1.68 kg Simply connect ahead of LED lamps LED failure is indicated The short circuit is indicated Serves all lines with replacement resistors Input cable 3,5m can be connected directly to the plug Operation voltage: 12V nominal Output current: 0.8A (Over current protection time delay 1...2000s !) Connection input: Sheathed cable 8x1mm², bare endings Connection output: Sheathed cable 8x1mm², bare endings Load imitation: 2x17 W (direction), 2x4W (rear lamp), 1x34W (stoplight) 1x17W (fog lamp), 1x17W (reversing lamp) Cable length input: app. 3,5m Cable length output: app. 1,2m Temperature range: -40...+75°C Electrical protection: Overcurrent, overtemperature, reverse polarity Mechanical protection: entirely sealed Dimensions: 280 x 70 x 25mm without cable outlet Mass: app. 1680g Failure monitor LEDs: 20mA (direction) 3mA (rear lamp) 8mA (stoplight) 8mA (fog lamp) 20mA (reversing lamp) Mounting rule: cooling plate 8dm² (aluminum sheet 1.5mm thickness) or on chassis frame

Read more less