Product overviewONE Light LED Driver 89090VR.90W 24V DC Dinrail constant voltage driver, IP20. Complies with standard EN61347-1 and any other specific standards.Key specifications
Product code: 89090VR
Type: LED Driver
Category: 22 Drivers
Family: The DIN RAIL Drivers
Material: Plastic
Length: 68mm
Width: 92mm
Height: 58mm
Warranty: 3 Years
Downloads & links
Datasheet
Manufacturer page
Professional inverter 12V to 230V AC for rough environmental conditions.▪ IN: 12V / OUT: 230V/50Hz▪ Input: 2x open cable ends▪ Output: open cable ends
Weight: 8 kg
waterproof
starts automatically, 5mA standby
perfectly suitable for fixed installation in service vehicle, separate socket
100% overload possible
Attention: no sinus, but almost all consumers can be connected
Input
voltage:
10 ... 15V DC
Output voltage:
225V +3% / -5%, 50Hz quartz-generated (115V/ 60Hz optional)
Output power:
600VA permanent, 1,200VA 10min, 12A (24A at 115V) 4sec
Connection input:
2x open cable end
Connection output:
open cable end
Cable length input:
2x app. 1200mm
Cable length output:
app. 2300mm
Current without load:
standby current 5mA RMS at 12V
Switching level:
start at 1W load
Current at 1W load:
1A at 12V
Overvoltage:
>16V, self-resetting
Undervoltage:
off at 10V, on at 11V
Efficiency:
app. 95% at 100% load / app. 80% at 10% load / app. 80% at
200% load
Electrical protection:
against reverse polarity, overtemperature, short circuit
Mechanical protection:
aluminum casting case IP66
Dimensions:
260 x 160 x 90mm (without screwings) without cable outlet
Mass:
app. 8,000g incl. Cables
Signalform:
step weave with fast PWM-modulation (to cos phi 0.2 at 50%
load)
Safety:
potential division with potential compensation (protective
conductor)
Product overviewONE Light LED Driver 89060VN.60W 24V DC constant voltage driver, Open Range IP20. Complies with standard EN61347-1 and any other specific standards.Key specifications
Product code: 89060VN
Type: LED Driver
Category: 22 Drivers
Family: The 24V DC Open Range Constant voltage
Material: Metal
Length: 111mm
Width: 78mm
Height: 36mm
Warranty: 3 Years
Downloads & links
Datasheet
Manufacturer page
Continuous contactors by design are predominantly used for drive functions on vehicles, they make and break slower than intermittent solenoids and are recommended for prolonged contact periods.
The SW80P features an enclosed top cover and offers environmental protection to IP66. The SW80P has M8 stud main terminals and 6.3mm spade coil connections. Mounted using supplied brackets, mounting can be horizontal or vertical, when vertical the M8 contact studs should point upwards.
SW84B-4 Albright
Magnetic Blowouts
These contactors are fitted with magnetic blowouts - denoted by 'B' suffix in the SW84B range) across contact gaps. These enable high currents to be ruptured very quickly so that arcing time is reduced to a minimum. Fitting of blowouts can make the contacts polarity sensitive and the positive markings on the top cover of the contactor must be observed.
About Continuous - CO.) SW84B-4 Solenoids
Continuous contactors by design are predominantly for drive functions on vehicles, they switch slower than intermittent solenoids and are recommended for prolonged contact periods.
The SW84 has M8 stud main terminals and 6.3mm spade coil connections. It can be mounted via M4 tapped holes or mounting brackets purchased as separate items. Mounting can be horizontal or vertical, when vertical the M8 contact studs should point upwards. Please note Normally Closed contacts are not suited to make and break load.
Product overviewONE Light LED Driver 89060VL.60W 24V DC constant voltage driver slim range ideal to install inside the profile, IP20. Complies with standard EN61347-1 and any other specific standards.Key specifications
Product code: 89060VL
Type: LED Driver
Category: 22 Drivers
Family: The 24V DC Slim Range Constant voltage
Material: Plastic
Length: 305mm
Width: 30mm
Height: 17mm
Warranty: 5 Years
Downloads & links
Datasheet
Manufacturer page
SW180-448L 24V Intermittent, 150 Amp
Intermittent contactors by design are predominantly used for hydraulic functions on vehicles, they make and break quicker than continuous solenoids and are not recommended for prolonged contact periods.
The SW180 has been designed for direct current loads, including motors as used on electric vehicles such as industrial trucks. Developed for both interrupted and uninterrupted loads, the SW180 is suitable for switching Resistive, Capacitive, and Inductive loads.
The SW180 features single pole single throw, double breaking main contacts with silver alloy tips, which are weld resistant, hardwearing and have excellent conductivity. The SW180 has M8 stud main terminals and 6.3mm spade coil connections. It can be mounted via M5 tapped holes or steel mounting brackets - supplied as separate items). Mounting can be horizontal or vertical, when vertical the M8 contact studs should point upwards.
ALBRIGHT 24V 250A INT DC ContactorThe SW200-281, a SW200 series of contactor is designed for direct current loads. SW200 have double breaking main contacts with silver alloy tips. Contact tips are weld resistant, extremely hard wearing. Normally Open contacts.
